• Format: ms-word (doc)
  • Pages: 65
  • Chapter 1 to 5
  • With abstract reference and questionnaire
  • Preview abstract and chapter 1 below

 5,000

ABSTRACT

This project was constructed with the desired materials of construction. The materials include aluminum, glass and wood.  Aluminum was used in forming the skeleton of the structure, glass was used for the doors while wood was used in the sides, top, base and partitions.

After building the skeleton of the structure with aluminum, other materials were used and made up the complete structure.  Materials like glass and wood.

Among the different types of glass available, the thick glass was used due to the fact that it offers greater resistance to hit than some thin glasses through the resistances is not much and can be broken by a fore more than fitty Newton – 50N.  The glass was cut into the measured dimensions by the equipment called “diamond”.  The diamond divides the glass perfectly according to the marker.

The wood used in the construction was cut with the aid of a saw and the edges smoothed with a file.  Both the wood and glass were held firm in the aluminum rail with the aid of a projected rubber.

The aluminum profiles were cut with the aid of an electrically powered machine cutter though manual cutters are available but electrical cutter reduces efforts.

TABLE OF CONTENTS

CHAPTER ONE

Introduction

CHAPTER TWO

2.0       Literature Review

2.1              Types Of Racks

2.1.1        Wall/Mini Racks

2.1.2         Industries Racks

2.2              Rack Protection

2.2.1        Fire Protection

2.3              Materials Of Construction

2.3.1        Aluminum

2.3.2         Bronzes

2.3.3         Wood

2.3.4         Glass

CHAPTER THREE

3.0       Constructional Procedure

3.1              Marking Out/Measurement

3.2              Cutting Operations

3.3              Filing Operations

3.4              Drilling Operations

3.5              Milling Operations

3.6              Coupling And Nailing

3.7              The Instruments

3.7.1        The Milling Machines

3.7.2        The Drilling Machines

3.7.3         The Tape

3.7.4         The Saw

3.7.5         The Diamond

3.8              Working Diagrams

3.9              Parts Of The Rack

CHAPTER FOUR

4.1              Discussion

4.2              Conclusion

4.3              Recommendation

References

Costing

INTRODUCTION

Racks are storage systems used in industries, homes, institutions etc.

Rock of interest of this project is the type of rack found in homes and some other institution.  This is a minim rack or wall rack as it is normally called.  This rack is hung on walls and partitioned within small ranges where material of small size can be kept.

Industries steel storage racks as they are known today did not exist 35 y ears ago.  Rail road cars filled with material in cardboard cartons were hand unloaded into four wheeled platform tracks that were pushed to the elevator of a multistioned ware house and the cartons hand unloaded into stacks on floors with 10 metres high ceilings.  People used the same various trucks to assemble orders from the various  stacks pushing the loaded truck to the elevator and then to the shipping dock where they were unloaded into vehicles for store delivery.  Such rudimentary distribution has been radically changed by some relatively simple innovations.

Forklift trucks have replaced man powered vehicles and loading methods.  They have been on the materials handling stage since the early 1900s and received their biggest impetus during World War II when forklifts were the logistical workhorses of the army and navy.

Unit loads of 2000 – 400016 that are easily picked up and transported by forklift trucks make highway trailer loading and unloading matter of minutes compared to the many hours for the hand unload method.

Industrial ware house buildings with one story ceiling heights of 30ft and wide column bay spalings replaced the multi stored ware houses and are ideally suited for use with the unit load and forklift concept.

Industrial steel storage racks proved to be the fourth necessary materials handling device to maximize the efficiency of the previous three because of “selectivity” and carton crish out.  If one unit load is tried on top of another up to 30ft ceiling height, the bottom load cannot be shipped unless the top ones are removed.

Computer technology has recently been added to all the foregoing to optimize the use and operation.  Today’s modern computes tell the distribution manager when to store the incoming unit loads, when and where to move to the picking face, the sequence in which to pick, and what and when to record.

All these component together have provided an efficient system that distributes the food, shelter and clothing of our oriented society.

GET THE COMPLETE PROJECT»

Do you need help? Talk to us right now: (+234) 08060082010, 08107932631 (Call/WhatsApp). Email: [email protected].

IF YOU CAN'T FIND YOUR TOPIC, CLICK HERE TO HIRE A WRITER»

Disclaimer: This PDF Material Content is Developed by the copyright owner to Serve as a RESEARCH GUIDE for Students to Conduct Academic Research.

You are allowed to use the original PDF Research Material Guide you will receive in the following ways:

1. As a source for additional understanding of the project topic.

2. As a source for ideas for you own academic research work (if properly referenced).

3. For PROPER paraphrasing ( see your school definition of plagiarism and acceptable paraphrase).

4. Direct citing ( if referenced properly).

Thank you so much for your respect for the authors copyright.

Do you need help? Talk to us right now: (+234) 08060082010, 08107932631 (Call/WhatsApp). Email: [email protected].

//
Welcome! My name is Damaris I am online and ready to help you via WhatsApp chat. Let me know if you need my assistance.